• PH:

    (435) 257-7000 


    8:00 am - 5:00 pm 


    8:00 am - 12:00 pm
Follow Us on Instagram View Our Page

Toro 5000 Series Rear Discharge 60" (152 cm) 25 HP EFI 747cc (72943)

Double tap to zoom



7-Gauge, High-Strength Steel

The TURBO FORCE deck is constructed of 7-gauge, high-strength steel which is 33% thicker and 32% higher in yield strength than ordinary 10-gauge commercial steel used in 7/10 decks. The combined effect is 75% stronger, so it easily handles the most demanding conditions and resists damage from impacts and abrasion.

A Flat Crisp Cut with Precision Blades

(.250) thick precision blades resist flexing to provide a flat, crisp cut. High-strength, heat-treated alloy steel survives impacts and provides resistance to the rapid wear commonly associated with abrasive conditions. Options include Recycler® and Atomic® mulching blades, medium sail Bahai blades, and low sail sand blades.

Deluxe Suspension Seat

Deluxe suspension seat features thick cushions, large bolsters and 3-D isolator mounts that absorb bumps and vibrations to reduce operator fatigue.

Smarter design in a bull-nose bumper.

7-gauge bull-nose bumper not only protects against frontal impacts, but also contains an integral underskirt to minimize blowout of debris and dust. The bottom, leading edge of the deck is raised 1/4" (6 mm), allowing grass to stand more upright when entering the cutting chamber, ensuring a level cut. Leaf "plowing" during spring and fall clean-up also is significantly reduced.

Smooth, Powerful Response

The new unitized pump and wheel motor use proven commercial hydraulic components while eliminating hoses and other potential leak points. You'll get a smoother, faster response while enjoying an even more reliable machine.

Operator Information Center

The instrument panel includes a digital hour meter, fuel gauge, and voltage meter, as well as diagnostic indicators for the safety interlock system.

Folding Rollover Protection System ROPS

A Rollover Protection System (ROPS), complete with seat belt, comes standard for operator protection in the case of accidental rollovers and tipovers. In situations where sufficient vertical clearance is not available, such as loading on an enclosed trailer, the ROPS can be temporarily unlocked and folded down.

Cast Aluminum Spindle

Cools quickly for enhanced durability and performance.


  • 25 HP (20 kw) Kohler® Command Pro® EFI 747cc Engine
  • 60" (152.4 cm) TURBO FORCE deck
  • The rear discharge design allows operators to trim on either side of the deck — no need to change direction to avoid discharging debris on roadways, sidewalks or flowerbeds.
  • EFI Fuel Efficiency - Kohler’s closed-loop EFI design improves fuel efficiency by up to 25 percent.


Engine 25 HP* (20 kw) Kohler® Command Pro EFI 747cc
Fuel Capacity Gas/12 gal (45.4 L)
Cutting Width 60" (152.4 cm)
Adjustable Discharge Baffle Standard
Air Filter Heavy-Duty Canister Air Cleaner
Armrests Standard
Blade Tip Speed 18,500+ ft/min (5638.8 m/min)
Blade Type .25 in (.6 cm) thick heat-treated steel
Carrier Frame 3" x 1.5" x 10 gauge (7.6 cm x 3.8 cm x 10 gauge)
Caster Tires 13" X 6.5" - 6" (33 cm x 16.5 cm - 15.2 cm) Flat-Free Semi-Pneumatic
Clutch Electromagnetic
Cup Holder Standard
Deck Design 80-Grade 7-gauge 60" (152.4 cm) TURBO FORCE® Rear Discharge w/ bull-nose bumper
Discharge Chute Rubber
Drive System Unitized Pumps 12cc/rev (shock valves) & Wheel Motors (14.6 cir)
Drive Tires 24" x 12" - 12" (61 cm x 30.5 cm - 30.5 cm)
Ground Speed 10 mph forward (16.1 kph)
Height of Cut 1 in - 5.5 in (2.5 cm x 14 cm) by .25 in (.6 cm) increments
Number of Blades 3
Hour Meter Standard
Hydraulic Fluid Premium synthetic
Ignition Electric
ROPS Folding; standard
Seat Handcrafted deluxe suspension seat with arm rests featuring bullhorn accent
Spindle Bearings Greaseless ball bearings
Spindle Housing 9" (22.9 cm) diameter cast aluminum
Steering Controls 1-5/8" (4.1 cm) diameter grips; adjustable, dampened
Weight 1,271 lbs. (576.5 kg)
Disclaimer *The gross horsepower of these engines was laboratory rated by the engine
manufacturer in accordance with SAE J1940 or SAE J2723. As configured to meet safety,
emission and operating requirements, the actual engine horsepower on these mowers will be
significantly lower.